Home     DIY Videos     Testimonials    ;Ordering    ;Our Facility    ; Canadian Customers    About      FAQ

Our Awnings:  15oz Heavy Duty for Slide Toppers      18oz Coated for Slide Toppers   Main Pull Down Patio Awning      Window Awnings      Carefree Omega      Over the Door Awnings      Awning Accessories   Privacy Panels

 

A&E RV SLIDEOUT AWNING
REPLACEMENT INSTRUCTIONS

Installing An A&E Slide Topper Is A Surprisingly-Manageable Job.
Check Out Our Slide Topper Replacement Videos To See For Yourself!

(One person can do this but is much easier with two)

I. Unroll old slide out awning fabric

With the slide room extended, unroll fabric by turning roller tube. This is easiest accomplished with one person at each end of roller tube as you are unrolling against the spring tension of the roller tube. You may also need a towel to keep your hands dry if there is moisture on the fabric as you, unroll it off the awning roller tube.

II. Pin the awning roller tube

The objective is to get the fabric totally unrolled and the bead attachment channel (where the fabric is attached to the roller tube) in a position that is easiest to work with. (approximately 12 to l o’clock) When it is in this position locate the hole in the main shaft of roller tube by looking through the slots in the end caps of the roller tube and “pin” or “lock” the roller tube by inserting something such as a cotter pin, long thin nail, small awl, etc. into the hole in the main shaft. Remove anti-billowing device if so equipped. (This is a collar screwed on the end of the roller tube to prevent the awning from unrolling while in transit)

Now you are ready to remove the old awning fabric.


A&E Awning pinned

III. Removing the old RV awning material

Inspect the awning rail on the RV for a screw at both ends of the awning fabric. Remove any screws and pull the old fabric out of the awning rail and the channel on the roller tube. It may take some extra effort to initially “free” the old fabric but should pull off relatively easy.

IV. Install new awning material

Inspect opening end of awning rail on RV. If the opening is questionable open it further with a pair of needle nose pliers. Also, file top and bottom edges to remove any burrs and rough edges. This is critical, as it is an easy area to tear the new fabric as it is installed. Do the same with the channel on the roller tube so the new fabric will install easier.


Open end of Roller Tube Channel

Install new fabric from either end-insuring top is up. The installer will be under the fabric installing the new fabric both on the RV and on the roller tube. While installing the new fabric keep the awning fabric as “horizontal” as possible as it is fed onto the awning rail and roller tube as it will slide on easier in this position. This part of the installation should be done “slow and easy” to insure the new fabric does not get torn. (A second person can be on the slide room taking up the slack but should not put much force on the fabric or they may pull the fabric on the awning rail too quickly and tear it. Patience is the key here. Center the fabric on the roller tube or place it where the old fabric was.


Feeding Fabric into Roller Tube

V. Test awning operation

Go back to roller tube, turn the roller tube to remove tension on the locking pin, remove the pin and allow roller tube to SLOWLY wind the new fabric onto the tube. Run the slide room in and out and observe if fabric needs to be moved in order for fabric to wind and unwind evenly onto the roller tube. Once this is accomplished install a screw into the awning rail on the RV at both ends to secure the awning fabric.

VI. Anti Billowing Device

Your awning may have an anti-billowing device which is a knob installed at one or the other end of the roller tube and is designed to engage a plate on the RV to keep the awning fabric from unraveling while going down the road. This knob should be approximately in the 1 o’clock position for slides on the driver's side and 11 o’clock for slides on the passenger side. These may change position because our fabric is heavier than the OEM’s fabric. If the position has changed simply, remove the screws holding it on, reposition to either 11 o’clock or 1 o’clock position, drill out new holes, and install in the correct position.


A&E Awning with Anti-Billowing Device

 

 


HOURS OF OPERATION: M-F 8-5 Pacific Standard Time

 

 

For questions call Tyler at: 360.980.0537
email: tyler@toughtopawnings.com

Our Awnings:    15oz Heavy Duty for Slide Toppers     18oz Coated for Slide Toppers      Main Pull Down Patio Awning     
Carefree Omega
    
Over the Door Awnings
    Window Awnings   Awning Accessories
    
Home   DIY Videos    Testimonials  ;Ordering  ;Our Facility  ;
Canadian Customers  ;About Us

Tough Top Awnings Purchasing and Shipping Procedure
Copyright © 2010–2013 Tough Top AwningsⓇ

Sign Up